Inter Troton Anticorrosion Isolation Primer 3:1 Kit (1Litre)

NZ $40.27 excl GST

Description

High quality 2K acrylic primer with anti-corrosion additives. It is a perfect isolating primer for car repairs. Perfectly protects sanded bare steel and isolates difficult surfaces and putties from topcoats, preventing mapping effects. Ideal spreading and fast drying time allows primer to be applied wet on wet. Does not require sanding.

It comes with 2 different kits, one is fast drying and the other is standard.

Advantages

Very good anticorrosive protection. of steel surfaces.
Strong adhesion to various substrates.
Very good isolating properties.
Short hardening time.
Suitable for wet on wet application.

Substrates

Wet on Wet Acrylic Primer 3:1 can be applied over:

Steel and aluminum after flatting and degreasing.
Zinc coated steel and galvanized steel after flatting and degreasing. S
anded glass polyester laminates (GFK/GRP). P
olyester body fillers and putties
Epoxy primers.
Wash primers.
Old coatings in good condition.

	Use For car repairs as an isolation primer for sanding or wet on wet application.
	Mixing ratio by volume Primer: 3 Hardener: 1 Thinner (black version): 35% for wet on wet, 15% for sanding. Thinner (grey and white versions): 35% for wet on wet, 20% for sanding. Mix thoroughly until a homogeneous consistency is obtained.
	Spraying viscosity Black version: 17÷18 seconds at 20°C thinner 35% about 30 seconds at 20°C thinner 15%. Grey and white versions: 17÷19 seconds at 20°C thinner 35%. about 30 seconds at 20°C thinner 20%.
	Pot life for the mixture about 40 minutes at 20ºC
	Number of layers For wet on wet: 1,5 layers; about 30µm of dry layer. For sanding: 1÷2 layers; about 50µm of dry layer. RP gun parameters Nozzle: 1,2÷1,6 mm; Pressure: 2,0-2,2 bar. HVLP gun parameters Nozzle: 1,3÷1,5 mm; Inlet pressure: 2,0 bar.
	Flash off time Between layers: about 5÷10 minutes before applying solvent base system: approx. 20 minutes before applying water base system: approx. 30 minutes Flash off time depends on the temperature and the number of layers
	Drying time Drying time at 20°C: Isolation primer /30÷50 µm/ ready for sanding ater 2÷3 hours. Drying time at 60°C Isolation primer /30÷50 µm/ ready for sanding after baking for about 15÷20 minutes and cooling down (approx. 1hour) Temperatures below 20°C significantly increases the hardening time.
	IR drying Isolation primer /30-50 µm/ : 5÷7 minutes under short waves. Primer for sending /50÷100 µm/: 8÷10 minutes under short waves. Do not exceed 60oC. Use as recommended by the equipment manufacturer. Wait about 10 minutes before starting IR drying.
	Dry sanding Machine sanding: P360÷P500. Manual sanding: P320÷P500. Wet on wet does not require sanding
	Wet sanding Machine sanding: P600÷P1000. Manual sanding: P800÷P1000. Wet on wet does not require sanding
	Further work 2K acrylic fillers can be directly over coated with: – 2K top coats. – 1K base coats. – 2K polyester putties – 2K acrylic primers
	General notes – Do not exceed recommended doses of the hardener! – The best repair results can be achieved at room temperature. The temperature in the body shop and the temperature of the product should be similar – When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and air ways. – The rooms should be well ventilated. – Clean the guns and equipment immediately after use. Caution: To maintain safety, always follow the instructions given in the MSDS for the products.