Home Sale

TMBACP

Inter Troton Anticorrosion Isolation Primer 3:1 Kit (1Litre)

NZ $39.10 NZ $24.95 excl GST
Sorry, the selected product is currently out of stock. Sorry, there are only 0 of this item currently in stock. the selected product is not available.

Inter Troton Fast Anticorrosion Isolation Primer 3:1 Kit (1Litre)

Sale, 2K Primers and Catalysts

Description

High quality 2K acrylic primer with anti-corrosion additives. It is a perfect isolating primer for car repairs. Perfectly protects sanded bare steel and isolates difficult surfaces and putties from topcoats, preventing mapping effects. Ideal spreading and fast drying time allows primer to be applied wet on wet. Does not require sanding.

It comes with 2 different kits, one is fast drying and the other is standard.
 

Advantages

  • Very good anticorrosive protection. of steel surfaces.
  • Strong adhesion to various substrates.
  • Very good isolating properties.
  • Short hardening time.
  • Suitable for wet on wet application.

Substrates

Wet on Wet Acrylic Primer 3:1 can be applied over:

  • Steel and aluminum after flatting and degreasing.
  • Zinc coated steel and galvanized steel after flatting and degreasing. S
  • anded glass polyester laminates (GFK/GRP). P
  • olyester body fillers and putties
  • Epoxy primers.
  • Wash primers.
  • Old coatings in good condition.
Screenshot 2024-02-08 130331

 
Zastosowanie
Use

For car repairs as an isolation primer for sanding or wet on wet application.

Proporcje mieszania
Mixing ratio by volume

Primer: 3
Hardener: 1
Thinner (black version): 35% for wet on wet, 15% for sanding.
Thinner (grey and white versions): 35% for wet on wet, 20% for sanding.

Mix thoroughly until a homogeneous consistency is obtained.

Lepkość natryskowa
Spraying viscosity

Black version:
17÷18 seconds at 20°C thinner 35%
about 30 seconds at 20°C thinner 15%.
Grey and white versions:
17÷19 seconds at 20°C thinner 35%.
about 30 seconds at 20°C thinner 20%.

Żywotność mieszanki
Pot life for the mixture

about 40 minutes at 20ºC

Liczba warstw
Number of layers

For wet on wet: 1,5 layers; about 30µm of dry layer.
For sanding: 1÷2 layers; about 50µm of dry layer.
RP gun parameters
Nozzle: 1,2÷1,6 mm; Pressure: 2,0-2,2 bar.
HVLP gun parameters
Nozzle: 1,3÷1,5 mm; Inlet pressure: 2,0 bar.

Czas odparowania
Flash off time

Between layers: about 5÷10 minutes
before applying solvent base system: approx. 20 minutes
before applying water base system: approx. 30 minutes
Flash off time depends on the temperature and the number of layers

Czas utwardzania
Drying time

Drying time at 20°C:
Isolation primer /30÷50 µm/ ready for sanding ater 2÷3 hours.
Drying time at 60°C
Isolation primer /30÷50 µm/ ready for sanding after baking for about 15÷20 minutes and cooling down (approx. 1hour)

Temperatures below 20°C significantly increases the hardening time.

Suszenie promieniem IR
IR drying

Isolation primer /30-50 µm/ : 5÷7 minutes under short waves.
Primer for sending /50÷100 µm/: 8÷10 minutes under short waves.

Do not exceed 60oC.
Use as recommended by the equipment manufacturer.
Wait about 10 minutes before starting IR drying.

Szlifowanie na sucho
Dry sanding

Machine sanding: P360÷P500.
Manual sanding: P320÷P500.

Wet on wet does not require sanding

Szlifowanie na mokro
Wet sanding

Machine sanding: P600÷P1000.
Manual sanding: P800÷P1000.

Wet on wet does not require sanding

Informacja
Further work

2K acrylic fillers can be directly over coated with:

– 2K top coats.
– 1K base coats.
– 2K polyester putties
– 2K acrylic primers

Informacja
General notes

– Do not exceed recommended doses of the hardener!
– The best repair results can be achieved at room temperature. The temperature in the body shop and the temperature of the product should be similar
– When working with 2K products, it is recommended to use personal protection equipment. Protect the eyes and air ways.
– The rooms should be well ventilated.
– Clean the guns and equipment immediately after use.

Caution: To maintain safety, always follow the instructions given in the MSDS for the products.

SDS

Questions?

In order to assist us in reducing spam, please type the characters you see:

Thank you for your interest.

Please enter your details and the document will be emailed to you immediately.

You might also be interested in ...

Farecla Mixing Cups and Lids 750ml Pack of 200
Out of Stock

Select Options

Farecla Mixing Cups and Lids 750ml Pack of 200

NZ $102.85